Force360 Max Repel+ Type 4,5,6 disposable coverall

The Force360 Max Repel+ is a single use protective coverall built around a 65gsm microporous material. The fabric pairs solid tensile strength with enough breathability to make a full day in the suit more bearable, which matters a lot when you are crouched in a confined space or working in the heat.

The detailing is what separates this one from a plain throwaway suit. The suit uses a two way zipper so you can unzip from the neck or the waist, a two layer folded stick down flap to keep liquids and particles away from the zip line, bound seams for added strength and barrier protection, and a three piece hood that moves with your head instead of fighting it. Thumb loops, a generous crotch and a bat wing back give you room to reach, squat and climb without the suit pulling tight at the shoulders. The thumb loops also stop the arms riding up when you lift them overhead.

The product name positions it as a Type 4,5,6 coverall and the listing describes it as an effective splash barrier against blood, body fluid and other infectious agents. If your task hinges on a formal protection class, confirm the exact standards and certification on the Done Right Safety product page or datasheet before you order in volume.

Matching the suit to the hazard

Start with the hazard, not the suit. The Max Repel+ is built for dry particulates and light liquid splash, and the listing flags it as a splash barrier against blood, body fluid and other infectious agents. If your job involves heavier liquid jets, a chemical hold-out requirement or a specific gas-tight class, check whether a higher-rated coverall is the right call. Where a formal protection class drives your decision, verify the standards and certification on the product page before committing.

Getting the size right

A disposable coverall only protects well if it is the right size. Too tight and the seams take strain when you bend; too loose and the spare material snags and tears. Check the size guide on the Done Right Safety listing and allow room for the base layer or workwear you will wear underneath. Once you are in it, hook the thumb loops over your thumbs so the arms stay put when you reach overhead, then run the two way zipper fully closed and press the stick down flap over the zip line so the join is covered.

Wearing it, then binning it

The Max Repel+ is single use protective gear, so treat it that way. Before each task, give the suit a quick look for nicks, open seams or a zip that will not seat. Use the waist release on the two way zipper if you need to vent or part-doff during a break, then re-seal the flap when you go back in. At the end of the job, remove it carefully so any contamination stays on the outside, and dispose of it in line with your site's waste procedure. Do not try to launder or reuse it.

The four coveralls compared here are all genuine like-for-like disposable coveralls from the Done Right Safety range, so this is a same-type comparison rather than a reach across product families. The differences come down to material construction, added features like reflective tape, and which products actually list formal standards.

Pick the Max Repel+ (CFPR180) when you want the Force360 microporous suit with the full feature set and a stated infectious agent splash barrier, and high vis is not a hard requirement. If you need workers to be seen, the Repel HV taped CFPR185 is effectively the same suit with a high vis, taped build. The Microgard 1500 trades some of that for a heavier three layer SMS material with anti-static treatment, which suits spray painting and grittier work.

The one practical point worth flagging: the Martula C500W is the only comparator here that spells out specific EN and ISO standards in its listing. If your procurement sign-off depends on seeing those numbers, that is a real reason to look at it, and a prompt to confirm what is certified on the Max Repel+ page before you decide.

On the listing, the Max Repel+ reads as a well thought out general purpose disposable coverall. The features that earn their keep are the ones you notice when you are actually working in it: the bat wing back and generous crotch that let you move, the thumb loops that keep the cuffs in place overhead, and the two way zipper with its covered flap for venting without exposing the zip line. The 65gsm microporous material is a sensible middle ground between durability and breathability.

What is confirmed is the construction and the comfort detailing, plus the listing's description of an effective splash barrier against blood, body fluid and other infectious agents. What is not spelled out in the information we have is the formal certification behind the Type 4,5,6 name. The standards field on this listing is empty, so treat the type wording as positioning until you have checked the product page or datasheet.

For most dry particle and light splash tasks this is an easy suit to recommend. If you are buying for a regulated application where the exact protection class has to be documented, do that verification first, or look at a comparator like the Martula that lists its standards openly.