Bisley hi-vis rain trouser with reflective tape

Wet shifts are the job these are built for, on crews that still have to be seen. The Bisley Hi Vis Rain Trouser is a hi-vis work pant built around a waterproof and breathable fabric, with all seams sealed so water stays on the outside. The waterproof rating is listed up to 20,000mm H20, which puts it well into proper rain gear territory rather than a light shower layer.

The shell is a 100% polyester Oxford with a PU coating in a 300D weight. Reflective tape runs around the lower leg for visibility, and the lower leg is finished in a contrast colour so the part that drags through mud and dirt does not show wear as quickly. A full elasticated waistband handles a range of body shapes, and the press snap hem opening lets you tighten or open the cuff over boots. Front angled pockets open to the body.

The reflective tape carries the AS/NZS 1906.4:2010 standard, and Bisley sizes the trouser from XS through to 6XL in a traditional fit. You can see the full size run and current colours on the product page at Done Right Safety.

Choosing the right pair

Start with the job. These are true rain trousers, so they earn their keep when you are outside in steady wet weather and still need to be seen. The 20,000mm H20 rating is a solid waterproof figure, and seam sealing matters as much as the fabric, because unsealed seams are where most so-called waterproof gear lets you down. If your work is dry and dusty, a drill work pant will serve you better day to day. For wet-shift visibility, this is the more focused tool.

On sizing, the traditional fit runs roomy enough to pull on over a base layer or your normal work pants, which is how a lot of people wear rain trousers. Bisley lists XS to 6XL, so check your usual size against the measurements on the product page before you order, and size up if you plan to layer underneath.

Fit and wearing in

The full elasticated waistband does the holding, so there is no belt to fuss with when you are throwing them on in a hurry. At the bottom, set the press snap hem so the cuff sits over your boot rather than tucking inside it, which keeps rain running off the boot instead of pooling in it. Check that the reflective tape on the lower leg is clear and not covered by overboots or gaiters.

Care and inspection

Treat the PU coating and the sealed seams with a bit of respect and they last. Rinse off mud rather than scrubbing hard, and let them dry naturally rather than near direct heat that can soften the coating. Before each wet season, look over the seam sealing for any lifting, and check the reflective tape for cracking or peeling, since damaged tape no longer meets its visibility job. Confirm the manufacturer's wash guidance on the product page or care label before laundering.

Both alternatives below are Bisley hi-vis work pants, so the real question is whether you need waterproofing or everyday hard wear.

Pick the BP6965T rain trouser when the weather is the problem and you need to stay dry and visible at the same time. The 20,000mm rating and sealed seams are the whole point, and the contrast lower leg helps it cope with the mud that comes with wet sites.

If your days are mostly dry, the BP6808T cotton drill pant gives you tougher everyday fabric, reinforced rise stitching and proper cargo and back pockets, plus it carries the additional AS/NZS 4602.1 garment standard. The BPC6431T cool vent cargo is the one to reach for in heat, where its mesh venting matters more than rain protection. All three are Bisley, so it is really about matching the fabric to your conditions.

As wet-weather hi-vis goes, this one ticks the boxes that actually matter. A 20,000mm H20 rating with fully sealed seams is genuine rain protection, not a token coating, and the breathable fabric is the thing that keeps you from getting just as wet from the inside. The contrast lower leg and press snap hem are practical touches that show Bisley knows these get worn on real sites.

Confirmed on the listing: the waterproof rating, seam sealing, the 300D polyester Oxford PU shell, lower-leg reflective tape to AS/NZS 1906.4:2010, the elasticated waistband, the size run from XS to 6XL, and the traditional fit. That is a clear picture of what you are buying.

Worth verifying on the product page or datasheet: the exact colours in stock, the breathability rating in numbers, and whether the garment carries a hi-vis class beyond the tape standard, since the pack only lists the reflective tape standard. If full hi-vis class compliance is a site requirement, confirm that detail before you commit.