Force360 Chemrepel HV Type 3,4,5,6 coverall

A 65gsm polyethylene laminated film does the work here: it keeps liquid chemicals and fine dry particles off the wearer's clothing and skin. Force360 lists the film as a barrier against many organic and inorganic liquid chemicals, and the seams are serged and then heat taped, which is the construction you want when splash and spray are part of the work.

The "HV" part is what sets this one apart from a plain chemical coverall. It carries 50mm reflective tape for better visibility, so it suits crews who need to be seen while they work in or around traffic, plant, or low light. You also get the practical fit details that make a long shift in a disposable suit bearable: an elasticised waist, hood, ankles and wrists, plus thumb loops that stop the sleeves riding up when arms go overhead.

A reinforced crotch is there for durability, and the three piece hood is shaped to move with your head rather than fighting it. If you want the full picture before you commit, the Done Right Safety product page is where the sizing, pack details and any rating documents live.

Match the suit to the hazard

Start with what you are actually protecting against. This coverall is built on a polyethylene laminated film, which Force360 describes as a barrier against many organic and inorganic liquid chemicals, plus high level dry particle and liquid penetration protection. That points it at splash, spray and dusty contamination work rather than heavy gas or full chemical immersion. Because no specific standard or type rating is listed on the hub for this item, confirm the protection class against your task on the Done Right Safety product page or the manufacturer datasheet before you rely on it. If your site brief calls for a named EN type or ISO rating, check that the documentation backs it.

Get the fit and the high-vis right

A disposable coverall only protects where it actually seals, so size it so you can crouch, reach and climb without straining the seams. Tuck in or seal the wrists and ankles, settle the elasticised waist, and use the thumb loops to keep the sleeves down when your arms are up. The three piece hood should sit close around the face. The 50mm reflective tape is the reason to pick this version, so wear it as intended and keep the tape clean and uncovered so it does its job in low light.

Inspect, wear once, and dispose

This is a single use suit. Check it out of the pack for any tears, open seams or damaged tape before you put it on, and discard any suit that is compromised. After the task, treat it as contaminated waste and dispose of it according to your site's procedure rather than reusing it. Keep spare suits in a clean, dry spot so the film and the taped seams are not degraded before first use.

The four Force360 coveralls compared here are all like-for-like disposable suits. The differences come down to fabric technology and whether the suit carries high-vis tape, which changes what each one is good at.

Pick the Chemrepel HV (CFPR301) when your task involves liquid chemical splash and the wearer also needs to be visible. It pairs the same polyethylene laminated film chemical barrier as the standard Chemrepel (CFPR300) with the 50mm reflective tape that the plain version does not list, so it is the obvious choice when high-vis is part of the brief and you do not want to give up the chemical barrier.

If chemical splash is the only concern and high-vis is not required, the plain Chemrepel (CFPR300) covers the same barrier. If heat is the bigger problem than chemicals, the Defender HV (CFPR184) trades the laminated film for a breathable SMS fabric aimed at hot and humid work while keeping reflective tape, and the Repel HV (CFPR185) sits in between with a breathable microporous fabric and a zip-protecting flap.

The listing confirms a 65gsm polyethylene laminated film coverall with serged and heat taped seams, described as a barrier against many organic and inorganic liquid chemicals and giving a high level of dry particle and liquid penetration protection. The fit details are well thought out for a disposable suit: elasticised waist, hood, ankles and wrists, thumb loops to keep sleeves down, a reinforced crotch, and a three piece hood. The 50mm reflective tape and the double inner and outer flap are the features that genuinely separate it from a plain chemical coverall.

The honest gap is ratings. The hub listing does not carry a specific EN type or ISO standard for this item, so the "Type 3,4,5,6" naming and any protection class should be verified directly on the Done Right Safety product page or the manufacturer datasheet before you specify it for a job. If your safety brief names a standard, confirm the paperwork matches it rather than assuming the product name is enough.

For a buyer who needs chemical splash protection and high visibility in one disposable suit, this is a sensible shortlist pick. Just go in with the right expectations on heat: a laminated film barrier is less breathable than an SMS or microporous fabric, so plan rest and rotation if the work is hot.