Pro Choice Viper earmuff, Class 5 26dB

The Viper is a Pro Choice over-the-head earmuff aimed at general purpose work where noise is a steady nuisance rather than an extreme hazard. It carries a Class 5 rating with an SLC80 of 26dB, which puts it at the protective end of the hearing protection scale for everyday tasks.

Pro Choice has built this one around comfort for longer shifts. The ear cups are solid but light, and the cushioning runs through both the ear cushions and the headband so the muff is not digging into you after an hour. The clamping force is kept low, so it presses lightly while still holding a snug seal around each ear.

If you are working in environments where noise climbs toward 110dB(A), this muff is rated to cover that range. You can read the full listing and order it on the Done Right Safety product page.

Matching the class to your noise level

Hearing protection classes run from low to high, and the class you need depends on how loud the environment is and how long you are exposed. The Viper is Class 5 with a 26dB SLC80 and is rated to noise up to 110dB(A). If your workplace has a noise assessment, check the measured level against that figure. Where noise sits below the rated limit, a Class 5 muff gives you headroom. If you are regularly at or above 110dB(A), you should confirm a higher attenuation option or layered protection on the product page or datasheet before relying on this muff alone.

Getting a proper seal

An earmuff only works when the cushions sit flat against the side of your head with nothing breaking the seal. Pull the cups down fully, settle the headband across the crown, and make sure hair, glasses arms, or hard hat straps are not lifting the cushion away from your skin. The Viper uses a low clamping force, so it should feel snug rather than tight. If you can slide a finger under the cushion or you hear noise leaking in, reseat it.

Care and replacement

Wipe the cups and cushions down with a damp cloth and let them dry before storing. Keep them out of direct heat and harsh chemicals, which can harden foam over time. Cushions and inner foam are the parts that wear. Once they go stiff, crack, or stop sealing cleanly, the attenuation drops, so plan to replace the cushions or the muff rather than pushing them past their useful life. Always check the listing for specific care guidance.

The earmuffs in the table below are like-for-like, same-type over-the-head models, so you can compare them directly on rating, attenuation and comfort features.

The Viper sits in the middle of this group on attenuation. If your noise levels are modest and you mainly want a comfortable, light, general purpose muff, the 26dB Viper covers the job up to 110dB(A). When the environment is louder, the Adder steps up to 32dB and is rated to 116dB, and the Force 360 Eco offers 28dB with hi vis cups for sites that want the worker easy to spot.

The Martula S1 leans on comfort, with 43mm foam inside ABS cups and a stainless steel 4 point suspension for even pressure, but its class and attenuation are not listed here, so confirm those on its product page if the protection level is the deciding factor.

The Viper is a sensible, no fuss general purpose earmuff. The listing is clear on the things that matter most: it is Class 5, has a 26dB SLC80, and is rated to noise up to 110dB(A). The comfort story is consistent too, with cushioned ear seals, an inner foam and headband cushion, and a low clamping force so it can be worn across a shift without becoming a chore.

The listing confirms the protection level and the comfort build. It does not spell out colour options, weight in grams, or any formal standards marking, so if you need a specific certification or a documented test result, verify that on the Done Right Safety product page or the datasheet before you commit.

For a buyer who needs reliable Class 5 cover for everyday noisy work and values a muff that stays comfortable, the Viper is an easy shortlist pick. If your noise levels are higher, look at the higher attenuation muffs in the comparison above.