Bisley drill coveralls

The Bisley Drill Coveralls (BC6007) are a heavy cotton work coverall built for the kind of dirty, knock-about jobs where you want one garment over the top of everything. The fabric is 100% cotton preshrunk drill at 310gsm, so it has real weight and body to it rather than the thin feel of a single-use suit.

What stands out is the pocket arrangement. There is a zippered chest pocket on the right, a tool-division chest pocket on the left, two angled side pockets that open to the body, a back patch pocket, a ruler pocket on the right, and a dedicated mobile phone pocket. The closure runs on metal press studs at the front and on the sleeve cuffs, and the knees are double layered for durability.

It comes in a size run from 77 to 117R. If you want a closer look at the listing before deciding, you can view the Bisley Drill Coveralls on Done Right Safety.

Picking the right size

This coverall runs from 77 to 117R, so check the size guide on the product page against the wearer's measurements before ordering. Cotton drill has a substantial hand and the fabric is preshrunk, which helps it hold its size through washing. If the coverall will go over winter layers or other workwear, allow a little room so the press studs do the closing rather than the seams taking the strain.

Getting the use right

The pocket setup is the reason to buy this one, so set it up to suit your day. Keep the things you reach for most in the tool-division and zippered chest pockets, drop a rule in the ruler pocket, and use the angled side pockets for hand access through to whatever you are wearing underneath. The double knee is there for kneeling work, so this is a sensible pick if you spend time down low. Note that the listed specifications give metal press studs for the front and cuffs rather than a heavy-duty zip, which is worth knowing if you are used to a zip-front coverall.

Care and getting a long life out of it

A 310gsm cotton drill coverall is made to be worn, washed and worn again, which is the main practical difference between this and a single-use suit. Specific wash temperatures and care instructions are not listed in the product specifications, so follow the care label and the guidance on the Done Right Safety product page. Check the press studs and the double-knee stitching from time to time, since those are the parts that take the most wear on a working coverall.

A fair word of warning before the table: these sit in the same broad coverall family but they are not like-for-like. The Bisley is a durable 100% cotton drill coverall built for repeat wear, while the comparators below are lightweight single-use protective coveralls designed for contamination control and limited liquid or particle exposure. Treat them as adjacent options for different jobs rather than direct substitutes.

The choice really comes down to what the coverall has to do. If the job is grease, grime and general site work, and you want something you can wash and wear day after day, the heavy cotton drill of the Bisley is the sensible pick. Its 310gsm fabric and double knee are built for that, where the 65gsm disposable suits are not.

If the task is contamination control, a light chemical splash or fine dust where you bin the suit at the end, then one of the single-use options fits better. The Alphatec adds high visibility stripes, the Force360 ChemRepel HV adds a chemical barrier film with 50mm reflective tape, and the Martula is the only one of the four with protection standards actually listed on the product page. Match the suit to the hazard rather than the other way around.

Read against its own specifications, the Bisley Drill Coveralls are a straightforward, well-specified cotton work coverall. The 310gsm preshrunk drill is genuinely heavy, the double knee is a real plus for anyone doing kneeling work, and the pocket count is generous: zippered and tool-division chest pockets, angled side pockets, a back patch and ruler pocket, and a phone pocket. That is a practical layout for a tradesperson who keeps a lot on them.

The two things to verify on the listing are sizing and care. The size run is given as 77 to 117R, so use the product page measurements to land the right fit, especially if it goes over other layers. Wash temperatures and care detail are not listed in the facts, so follow the care label.

One honest point: the product is listed under a disposable coverall label in places, but the specifications describe a durable, reusable cotton garment, not a single-use suit. No protective standards or ratings are listed for it, so do not treat this as certified chemical or particulate PPE. If you need a coverall to a specific protection standard, confirm that on the Done Right Safety product page or datasheet before you order.